Product ID:ACTIVATOR BA-5
MSDS Date:10/04/1989
FSC:8040
NIIN:00-023-7719
MSDS Number: BJXFK

BACON INDUSTRIES, INC.

192 PLEASANT STREET
WATERTOWN, MA 02172
US

Emergency Phone: 617-926-2550/714-863-1499

Info Phone: 617-926-2550/508-668-6753

Cage: 99098

BACON INDUSTRIES, INC.

WATERTOWN, MA 02172 US

Telephone: 617-926-2550

Cage: 99098

N-(AMINOETHYLAMINOETHYL) IMIDAZOLIDINE

Fraction By Weight: 90%

COBALT CHROMITE BLUE GREEN SPINEL (PIGMENT BLUE 36)

CAS: 68187-11-1

Fraction By Weight: 3%

OSHA PEL 0.1 MG/M3

ACGIH TLV: 0.1 MG/M3

SILICA (*MATERIAL IN NON-AIRBORNE FORM)

CAS: 112945-52-5

RTECS: VV7310000

Fraction By Weight: 7%

OSHA PEL 20 MPPCF

ACGIH TLV: 20 MPPCF

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:LONG TERM EFFECTS HAVE NOT BEEN FULLY
DEFINED ALTHOUGH LONG-TERM CONTACT MAY CAUSE SENSITIZATION.
Effects of Overexposure:INGESTION:HARMFUL IF
SWALLOWED.INHALATION:HEADACHE,NAUSEA,DIZZINESS & RESPIRATORY
IRRIT.SKIN:MAY CAUSE SEVERE SKIN INJURY(REDDENING &
SWELLING).SENSITIZER-CAN CAUSE ALLERGIC REACTION WHICH MAY BE SEVE
RE IN CERTAIN INDIVIDUALS.EYES:MAY CAUSE SEVERE EYE INJURY.VAPORS
MAY CAUSE MINOR INJURY WHICH MAY LAST SEVERAL DAYS.
Medical Cond Aggravated by Exposure:THIS MATERIAL MAY AGGRAVATE
ASSORTED SKIN AND EYE CONDITIONS SUCH AS ECZEMA, PSORIASIS AND
DERMATITIS.

First Aid:EYES:IMMED FLUSH W/LOTS OF WATER FOR 15 MIN.CONTACT DOCTOR
IMMED.SKIN:IMMED WASH W/SOAP/WATER.IF IRRIT PERSISTS CONTACT DOCTOR
IMMED.INHALATION:MOVE TO FRESH AIR IF SYMPTOMS OCCUR.IF BREATHING
HAS STO PPED,GIVE ARTIFICIAL RSPRTN.KEEP AFFECTED PERSON
WARM/QUIET.GET MED ATTN.INGESTED:CALL DOCTOR/POISON CONTROL CENTER
IMMED.GIVE 1 TO 2 GLASS OF WATER.DO NOT GIVE ANYTHING BY MOUTH TO
UNCONCIOUS PERSON

Flash Point Method:TCC
Flash Point:64F/18C
Extinguishing Media:WATER FOG, CARBON DIOXIDE, DRY CHEMICAL OR ALCOHOL
FOAM.
Fire Fighting Procedures:WEAR POSITIVE SELF-CONTAINED BREATHING
APPARATUS AND FULL PROTECTIVE CLOTHING, COMBUSTION PRODUCTS MAY
CAUSE BURNS. AVOID BREATHING SMOKE.
Unusual Fire/Explosion Hazard:WHEN THE MATERIALS ARE EXPOSED TO HEAT IN
CLOSED CONTAINERS PRESSURE WILL BUILD. KEEP NON-IGNITED MATERIAL
COOL WITH WATER SPRAY.

Spill Release Procedures:MOVE ALL SOURCES OF IGNITION.WEAR PROTECT
APPARATUS & OTHER PROTECT EQUIP.COLLECT SPILLED MAT'L & CLEAN UP
THE RESIDUE WITH AN INERT,ABSORBENT
MATERIAL(SAND,VERMICULITE,ETC.)PLACE IN A U.S. DEPT OF TR
ANSPORTATION APPROVED METAL CONTAINER &SEAL.

Handling and Storage Precautions:STORE 80F/BELOW.AVOID EYE/SKIN
CONTACT.DO NOT WEAR CONTACT LENSES WHILE IN THE VICINITY WHERE
BEING USED.
Other Precautions:SOME COMPONENTS OF THESE FILLERS CLASSIFIED AS
HAZARDS IN THEIR AIRBORNE FORM.IF CURED AND
MACHINED,CUT,SANDED/HANDLED IN A WAY TO RELEASE PARTICLES INTO AIR
PROPER CARE MUST BE TAKEN TO NOT INHALE DU ST.*

Respiratory Protection:GOOD LOCAL VENT OR A NIOSH ORGANIC FUME
RESPIRATORY IS RECOMMENDED IN POORLY VENTILATED AREAS OR WHEN
MATERIAL IS AT ELEVATED TEMPS. SCBA IS RECOMMENDED FOR LARGE
QUANTITIES IN POORLY VENTILATED AREAS WHICH HAVE A HIGH VAPOR
CONCENTRATION.
Ventilation:LOCAL EXHAUST.MECHANICAL VENT MAY BE ACCEPTABLE WHEN SMALL
AMOUNTS ARE USED AT ROOM TEMP.VENT CURING OVENS OUTDOORS.
Protective Gloves:IMPERVIOUS LATEX OR RUBBER GLOVES.
Eye Protection:FACE SHIELD/GOGGLES SHOULD BE MANDATORY
Other Protective Equipment:WHERE SKIN CONTACT CAN OCCUR WEAR
COVERALLS,APRON/RUBBER FOOT COVERINGS.SAFETY SHOWER/EYE WASH
FACILITY SHOULD BE AVAIL.
Work Hygienic Practices:GOOD PERSONAL HYGIENE.CLOTHING CONTAMINATED
WITH THIS MAT'L SHOULD BE WASHED BEFORE REUSING.
Supplemental Safety and Health
*DO NOT ALLOW CONTACT WITH COPPER, COPPER ALLOY, ALUMINUM OR ALUMINUM
ALLOY MATERIALS. BULK STORAGE SHOULD BE UNDER NITROGEN OR ARGON
BLANKET.

Boiling Pt:B.P. Text:370F,188C
Vapor Pres:<0.01@20C
Vapor Density:> 1
Spec Gravity:1.1
Viscosity:250 CP
Evaporation Rate & Reference:< 1
Solubility in Water:APPRECIABLY MISCIBLE
Appearance and Odor:GREEN LIQUID PASTE WITH AMMONICAL ODOR
Percent Volatiles by Volume:NIL

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, ACIDS, HALOGENATED ORGANIC COMPOUNDS,
ALDEHYDES, KETONES, ANHYDRIDES AND ACRYLATES.
Stability Condition to Avoid:EXCESSIVE HEAT
Hazardous Decomposition Products:NITROGEN OXIDES, CARBON DIOXIDE,
CARBON MONOXIDE, ALDEHYDES AND OTHER HAZARDOUS ORGANICS.
Conditions to Avoid Polymerization:MAY OCCUR WHEN MIXED WITH AN EPOXY
RESIN AT ELEVATED TEMPERATURES (>150F) ESPECIALLY IN QUANTITIES
GREATER THAN ONE LB.

Waste Disposal Methods:INCINERATE OR LANDFILL IN ACCORDANCE WITH
APPLICABLE FEDERAL, STATE AND LOCAL REGULATIONS. DO NOT CONTAMINATE
LAKES, STREAMS, PONDS OR UNDERGROUND WATER SUPPLY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.